B)ĭesign of Differential Filters for High-Speed Signal Chains (Rev.Xf86-video-intel: Branch 'display-port' - 194 commits - acinclude.m4 configure.ac. High-Speed, Analog-to-Digital Converter BasicsĪ Glossary of Analog-to-Digital Specifications and Performance Characteristics (Rev. ULP Temperature-Compensated RTC on MSP430F6736 MSP430 Advanced Power Optimizations: ULP Advisor SW and EnergyTrace Technology A)ĭesigning With MSP430™ MCUs and Segment LCDs (Rev. A)Ī world of possibilities: 5 ways to use MSP430™︎ MCUs in your designĪnswers to Common Sigma-Delta ADC Questions on MSP MCUsĭifferences Between MSP430F67xx and MSP430F67xxA Devices (Rev. MSP430 System-Level ESD Considerations (Rev. Implementation of a Single-Phase Electronic Watt-Hour Meter Using MSP430F6736(A) (Rev. ![]() MSP430x5xx and MSP430圆xx Family User's Guide (Rev. ![]() MSP430F6731A Microcontroller Errata (Rev. MSP430F673xA, MSP430F672xA Mixed-Signal Microcontrollers datasheet (Rev. The MSP430F673xA and MSP430F672xA devices are microcontrollers with high-performance 24-bit sigma-delta ADCs (three ADCs in MSP430F673xA and two ADCs in MSP430F672xA), a 10-bit ADC, four eUSCIs (three eUSCI_A modules and one eUSCI_B module), four 16-bit timers, a hardware multiplier, a DMA module, an RTC module with alarm capabilities, an LCD driver with integrated contrast control, an auxiliary supply system, and up to 72 I/O pins in the 100‑pin devices and 52 I/O pins in the 80‑pin devices.įor complete module descriptions, see the MSP430F5xx and MSP430F6xx Family Users Guide. The DCO allows the device to wake up from low-power modes to active mode in 3 µs (typical). The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The TI MSP family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. Energy Measurement Design Center for MSP430™ MCUs.Single-Phase Electronic Watt-Hour Meter Development Tool (Also See Tools and Software).Available in 100-Pin and 80-Pin LQFP Packages.Device Comparison Summarizes the Available Family Members.Serial Onboard Programming, No External Programming Voltage Needed.Up to Six External Channels and Two Internal Channels, Including Temperature Sensor.Hardware Multiplier Supports 32-Bit Operations.Integrated LCD Driver With Contrast Control for up to 320 Segments in 8-Mux Mode.Three 24-Bit Sigma-Delta Analog-to-Digital Converters (ADCs) With Differential PGA Inputs.Separate Voltage Supply for Backup Subsystem.Password-Protected RTC With Crystal Offset Calibration and Temperature Compensation.Enhanced UART Supports Automatic Baud-Rate Detection.Enhanced Universal Serial Communication Interfaces (eUSCIs).Three 16-Bit Timers With Two Capture/Compare Registers Each. ![]() One 16-Bit Timer With Three Capture/Compare Registers.Low-Frequency Trimmed Internal Reference Source (REFO).Low-Power Low-Frequency Internal Clock Source (VLO).FLL Control Loop for Frequency Stabilization.System Operation From up to Two Auxiliary Power Supplies.Supply Voltage Supervision, Monitoring, and Brownout.Fully Integrated LDO With Programmable Regulated Core Supply Voltage.16-Bit RISC Architecture, Extended Memory, up to 25-MHz System Clock.Wake up From Standby Mode in 3 µs (Typical).Real-Time Clock (RTC) With Crystal, Watchdog, and Supply Supervisor Operational, Full RAM Retention, Fast Wake up:ġ.7 ♚ at 2.2 V, 2.5 ♚ at 3.0 V (Typical)įull RAM Retention, Supply Supervisor Operational, Fast Wake up: 265 ♚/MHz at 8 MHz, 3.0 V, Flash Program Execution (Typical)ġ40 ♚/MHz at 8 MHz, 3.0 V, RAM Program Execution (Typical)
0 Comments
Leave a Reply. |